Effect of AMC on fixed‐rate traffic with hard delay constraints in mobile broadband systems

The adaptive modulation and coding (AMC) technique, which has been adopted by advanced mobile telecommunication systems, supports a flexible response to the random radio behaviour. As a result, the attained transmission rate over a wireless link is time varying. Hence, resource demands are not deterministic but fluctuating even for calls with constant bit rate service requirements. Consequently, constant bit rate calls are susceptible to a forced call termination because of insufficient resources not only in a target cell during inter‐cell handoffs but also in a serving cell during radio link deterioration. Furthermore, call blocking and dropping probabilities depend on radio propagation conditions among other factors and therefore they are dissimilar throughout a service area. The latter leads to unfairness problems. We analytically measure the impact of AMC on fixed‐rate service with hard delay constraints such as voice for different signal, mobility and traffic conditions. We consider a reference case (call requests are admitted into the system provided there are enough free resources) and two classes of admission control approaches: traditional (only inter‐cell handoffs are prioritised) and modified (all ongoing calls are prioritised). The reported results reveal conditions for which AMC affects voice call performance and can serve as guidelines on admission control design. Copyright © 2013 John Wiley & Sons, Ltd.     

Characterization of CVD Bonded Tyranno® Fibers Oxidized at High Temperatures

The oxidation of highly porous ceramic matrix composites (PCMCs) based on different Tyranno^® fibers has been analyzed by means of thermogravimetry and electron microscopy. Both uncoated fibers and PCMC materials exhibit parabolic kinetics between 900°C and 1250°C, these being faster for Ti‐doped than for Zr‐doped Tyranno fibers. Oxide layers in Ti‐doped fibers are porous and partially crystalline, whereas in Zr‐doped materials a significant fraction of relatively coarse β‐SiC grains is still found embedded in the amorphous silica matrix. On the other hand, the CVD‐SiC coatings exhibit higher oxidation rates from the outer surface than from the inner one, a phenomenon that has been associated not only with the more difficult access of oxygen to the inner face but also with the highly <111>  textured structure of these coatings, for which very different oxidation rates have been published for the inward and outward directions. Cracking phenomena observed above 1100°C for long dwelling times do not lead to an acceleration of the oxidation process, which could be due to the simultaneous crystallization of the amorphous silica layers.     

Identification,Synthesis, and Behavioral Activity of 5,11-Dimethylpentacosane,A Novel Sex Pheromone Component of the Greater Wax Moth,Galleria Mellonella (L.)

The greater wax moth, Galleria mellonella (L.), is a serious and widespread pest of the honeybee, Apis mellifera L. In contrast to most moths, for which long-range mate finding is mediated by female-produced sex pheromones, G. mellonella males attract conspecific females over long distances by emitting large amounts of a characteristic scent in combination with bursts of ultrasonic calls. The male scent for this species was previously identified as a blend of nonanal and undecanal. When these compounds were bioassayed, characteristic short-range sexual behavior, including wing fanning, was triggered in conspecific females, but the aldehyde blend failed to elicit attraction over longer distances. We identified, via analysis and synthesis, a third male-specific compound, 5,11-dimethylpentacosane. We show that it acts as a behavioral synergist to the aldehydes. In wind tunnel experiments, very few female moths responded to the aldehyde blend or to 5,11-dimethylpentacosane tested separately, but consistently showed orientation and source contact when a combination of all three compounds was applied. The level of attraction to the three-component mixture was still lower than that to male extract, indicating that the composition of compounds in the synthetic blend is suboptimal, or that additional pheromone components of G. mellonella are yet to be identified. The identification of 5,11-dimethylpentacosane is an important step for the development of an efficient long-range attractant that will be integrated with other environmentally safe strategies to reduce damage to beehives caused by wax moths.     

Physical and Functional Properties of Blackberry Freeze- and Spray-Dried Powders

The aim of the present work was to develop two products from blackberry juice by freeze and spray drying with potential use as food colorants or healthy ingredients. A characterization of the physical and functional properties of the powdered juices was done. Maltodextrin or a mixture of trehalose and maltodextrin were assessed as carrier matrices. Freeze-dried, maltodextrin-containing powders presented the best retention of bioactive compounds and antiradical activity; however, they showed a narrow relative humidity range for storage in the glassy state. Spray-dried powders showed better physical properties, bearing higher glass transition temperature and lower molecular mobility than freeze-dried formulations.     

Design of Porous Alginate Hydrogels by Sacrificial CaCO3 Templates: Pore Formation Mechanism

Fabrication of porous alginate hydrogels with a well‐controlled architecture useful for tissue engineering is still a challenge. Here, CaCO₃‐based templating is utilized to design stable alginate gels with controlled pore dimensions in the range of 5–50 μm. The mechanism of pore formation is studied considering two factors affecting the pore size: i) osmotic pressure generated during the dissolution of sacrificial CaCO₃ templates and ii) alginate gel network density. Osmotic pressure can achieve an upper limit of 100 MPa but does not affect the gel porosity. Additional osmotic pressure (range of kPa) induced by dextrans pre‐encapsulated into CaCO₃ vaterite is also insufficient for pore enlargement. Pore stability depends merely on the gel network density and on the number of crosslinking calcium ions provided locally per unit time; pores are collapsed when template dissolution is too slow or if there is insufficient alginate concentration (below 2%). Young's modulus indicates the soft nature of the prepared hydrogels (tens of kPa) applicable as soft porous scaffolds with a tuned internal structure.     

An Application of Computer‐Aided Molecular Design (CAMD) Using the Signature Molecular Descriptor–Part 2. Evaluating Newly Identified Surface Tension‐Reducing Substances for Potential Use as Shrinkage‐Reducing Admixtures

In this study, the use of computer‐aided molecular design (CAMD) is validated as a tool for enabling the discovery of new shrinkage‐reducing compounds for possible use in portland cement composites and is framed as one of many multiscale modeling tools in a broad hierarchy of possibilities. Twelve additives were tested for their ability to inhibit shrinkage in Type I ordinary portland cement under both autogenous and drying conditions. The 12 additives included two commercial shrinkage‐reducing admixtures (SRAs), two active ingredients of a commercial admixture [one of which was used to establish the quantitative structure–property relationships (QSPR)], two additional classified as potential SRA compounds based on the patent literature, four newly identified compounds predicted by using CAMD and an inverse quantitative structure–property relationship (I‐QSPR), and two other compounds use to establish the QSPR relationship. The newly identified I‐QSPR compounds were targeted for their ability to reduce the surface tension of water, a primary consideration for shrinkage‐reducing activity. Results for both drying shrinkage and autogenous shrinkage indicate that the designed compounds perform similar to commercial admixtures, yet have different chemical functionalities. Hydration data and set measurements were also considered since selection of new SRAs is a multiparameter problem with many constraints. Thus, these newly identified shrinkage‐reducing compounds can potentially provide additional options for use in portland cement concrete applications.     

Laser-Deposited In Situ TiC-Reinforced Nickel Matrix Composites: 3D Microstructure and Tribological Properties

A new class of Ni-Ti-C-based metal-matrix composites has been developed using the laser-engineered net shaping? process. These composites consist of an in situ formed and homogeneously distributed titanium carbide (TiC) phase reinforcing the nickel matrix. Additionally, by tailoring the Ti/C ratio in these composites, an additional graphitic phase can also be engineered into the microstructure. Serial-sectioning, followed by three-dimensional reconstruction of the microstructure in these composites, reveals homogeneously distributed primary and eutectic titanium carbide precipitates as well as a graphitic phase encompassing the primary carbides within the nickel matrix. The morphology and spatial distribution of these phases in three dimensions reveals that the eutectic carbides form a network linked by primary carbides or graphitic nodules at the nodes, which suggests interesting insights into the sequence of phase evolution. These three-phase Ni-TiC-C composites exhibit excellent tribological properties, in terms of an extremely low coefficient of friction while maintaining a relatively high hardness.     

Identification and Effects of Interaction Phytotoxic Compounds from Exudate of Cistus ladanifer Leaves

Eleven allelochemicals (ferulic acid, cinnamic acid, 4-hydroxybenzoic acid, hydroxycinnamic acid, methyl propionate, oxalic acid, methylmalonic acid, p-anisic acid, butyric acid, 3-hydroxybutyric acid, and azulene) were identified in the exudate of Cistus ladanifer L. We studied the effect of each on germination, cotyledon emergence, root length, and cotyledon length of Rumex crispus. Three groups were distinguished with respect to phytotoxic activity: compounds with low activity (ferulic acid, 4-hydroxybenzoic acid, oxalic acid, methylmalonic acid, p-anisic acid, hydroxybutyric acid, and azulene), with intermediate activity (cinnamic acid and hydroxycinnamic acid), and with high activity (methyl propionate and butyric acid). The effect of the interaction of the compounds was studied. When acting conjointly, all combinations tested produced a more negative effect on both germination and seedling growth than when acting alone. The interaction affected cotyledon emergence and root length more negatively than germination and cotyledon length. When hydroxycinnamic acid and cinnamic acid were added to these mixtures there was an enhancement in the phytotoxic activity, accentuating the effect of the other allelochemicals.     

Two-Step Processing Method for Blending High-Performance Polymers with Notable Thermal and Rheological Differences: PEI and PBT

Blends between high-performance polymers (HPP) are barely studied, especially those produced by melting processing. In this work, it is proposed a novel methodology to prepare blends between polymers with notable processing temperature differences: poly(ether imide) (PEI) and poly(butylene terephthalate) (PBT). Processing parameters are settled after thermal and rheological evaluation of pure materials, those results suggest these blends need to be produced by steps. It is found a synergistic effect such as lowering PEI processing temperature and reducing PBT hydrolysis at high temperatures. Propose methodology allows to produce blends between HPP in the whole composition range with the same processing conditions.